ADE NUWA RD3-021 Ultra Red Dot Sight 2 MOA dot with top battery compartment for RMSC footprint

ADE NUWA RD3-021 Ultra Red Dot Sight 2 MOA dot with top battery compartment for guns with RMSC footprint.

ADE NUWA is the first (and so far the only) red dot with RMS/RMSc footprint that has a TOP BATTERY LOADING system, no need to Remove the sight to change the Battery that requires re-sight in and waste ammo.

Battery life (CR1632) approximately 100-300 hours depending on the brightness setting.
Hard coated aircraft aluminum and multi-coated glass.

- 2 MOA Red Dot.
- Weight 15.5 grams (0.55oz)
- Length 1.5"
- Width 0.88"
- Height 0.89"
- Auto shutoff time 90 minutes
- 8 Brightness settings
- Recoil graded 9mm
- Waterproof: no

Comes with screws for several Optics Ready handguns. Does not come with any mounting plate such as picatinny mount or plate made for a specific handgun. The screw pattern also fits the separately available ADE Glock rear sight replacement Picatinny rail, so you can mount this Red Dot to most NON MOS Glock models.

Ade Nuwa created an iron sight at the end of the body, and also added two white dots on the curve, for the rear part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distance/gap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight

For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacturer equipped rear sight, ADE NUWA's rear white dot will act as a pistol factory original rear sight for Co-Witness.

ADE Nuwa is manual activated by pressing the on/off switch. Press and Hold switch for 2 seconds to turn on/off, quick press to adjust the brightness from low to high.

For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacturer equipped rear sight, ADE NUWA's rear white dot will act as a pistol factory original rear sight for Co-Witness.

Comes with 3 pairs of screws for Sig P365XL/X, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cut/slide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.

ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you can’t get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size.

Designed to fit:
Bul Armory SAS II lightweight 3.25 Comp
Canik Elite TP9 SC
Canik METE SFX
Canik METE SFT
Canik METE MC9
Sccy cpx-2
FN Reflex™ MRD
Sig P320 Xten (Using Sig provided plate marked for Leopold Deltapoint Pro optic footprint)
Sig P322
Sig P365-380(make sure your model is exactly called "P365-380", not P360 or P380)
Sig P365X/P365XL/P365XL SPECTRE COMP
Sig P365 X Macro
Sig P365 California Compliant (Sig released it in late 2023/early 2024)
Ruger Max-9
Glock 43X MOS/48 MOS(not compatible with regular glock 43x/48 that are not MOS)
Springfield Hellcat OSP
Springfield XDS MOD 2 OSP
Springfield Elite 3.8” Compact OSP 9mm
S&W Shield 2.0 Optics Ready
S&W 9mm Equalizer
S&W M&P9 shield plus Optics Ready
S&W MP9 EZ
S&W MP 5.7
S&W M&P shield plus performance center
Walther PPS M2 Optics Ready
Kimber Mako7
Girsan MC1911SC Ultimate
Mossberg MC2SC/MC2c
Masada SLIM
Taurus GX4 Toro
Rock Island STK-100
PSA Rock 5.7

Plus any pistol/mounting plate/slide with RMS/RMSC screw pattern/footprint.